image
3179 Green Valley Road • Birmingham, AL 35243-3723 • Office: (205) 968-3570 • Fax: (205)-968-1503


One New WDM Initial PinchSheet & Plate Bending Roll

One New WDM Hydraulic Double Pinch Plate Bending Machine  

One Preowned 8' Mechanical Plate Roll

One Preowned Heller Initial Pinch Mechanical Plate Roll

One Preowned Webb 3 Roll Initial Pinch Plate Roll

One New Americor Plate Bending Roll


 

One New WDM Initial Pinch Sheet & Plate Bending Machine

 

Specifications 

          5 Horsepower TEFC main drive motor 
          NEMA 12 electrical enclosures 
          Electrics to NFPA 79 specifications 
          230/460 volt 3 phase 60 hertz electrics 
          6 diameter 1045 steel rolls 
          14 FPM rolling speed 


Features

            All gear drive 
            Sealed ball & roller bearings on all rolls and idler gears 
            Unique high torque hydraulic drive system 
            High quality American made hydraulic components 
            Independent adjustment of the pinch roll via a handwheel-wedge-screw arrangement 
            Alloy steel bearing cases and wedges 
            Bending roll adjusted with handwheel via bronze worm gear/alloy steel screw arrangement, tiltable for cone rolling 
            Instant start, stop, and reverse via guarded foot pedal 
            Safety cable on three sides of the machine 
            Swing-out top roll for easy workpiece removal 
            Starting groove in pinch roll to facilitate rapid workpiece prebending and rolling 
            Aluminum scale and pointer to show bending roll position 
          Haze gray epoxy and safety blue enamel finish 

Optional Equipment Installed

         
Cone rolling attachment
          Hardened and polished rolls (55-60 Rc)
          Circular grooves for rolling sheets with wired edges or rod bar        stock
          Power bending roll adjustment 


Componenent Suppliers

         
Torrington, Browning, Eaton/Charlynn, SKF, Morse, Hoffman,                   Red Lion, Linn Gear, Prince, 
           HydraForce, McGill, Lincoln, Peer, Square D 


     The rated rolling capacity for this machine is 1/4” mild steel plate                        to   24” diameter by 5’ wide 


        This machine weighs approximately 3,000 pounds. 

 

Price

Delivery

Terms

F.O.B.

$ 25,785.00

Stock, Subject to Prior Sale

Net before Shipment

Point of Destination

         from Warehouse


 


 

 

 One New WDM Hydraulic Double Pinch Plate Bending Machine

Standard Features

      1045 carbon rolls 
      Hydraulic driven rolls which provide instant start, stop, and reverse 
      NEMA 12 control cabinet fuse control transformer 
      Electrics meet NFPA 79 specifications 
      Thermal overload protection 
      Two roll drive 
      SKF Spherical roller bearings on all main bearings 
      LSHT type hydraulic drive motor with high volumetric and overall efficiency 
      Infinitely variable speed from 0 to 22 FPM 
      Safety cable around perimeter of machine 
      Machine is controlled by hydraulic directional valves located on machine drive housing 
      Rolls driven through planetary or spur gear type speed reducers with brake, (s) 
      Dial/pointer type indicators to show roll position 
      Machine sets directly on level floor 
      Ability to roll symmetrical steel sections without additional attachments 
      Hydraulic operated drop end support 
      Component suppliers include some or all of the following: SKF, Torrington, Continental, Auburn, 
      White, Torque Hub, Telemechanique, Modular Controls, Hoffman, Red Lion, Morse, Hydra, 
      NTN, WRG Gears, Prince, Browning, HydraForce, Double A 

Optional Equipment Installed 

          Cone Attachment 
          Hardened and polished rolls (55-60c) 


Price: $86,992.00 = 403-8-6 with standard and noted optional equipment and 425 control
Price: $73,997.00 = 403-8-6 with standard and noted optional equipment and 423-3-LP2-RC                             Control
Price: $64,004.00 = 403-8-6 with standard and noted optional equipment and Beta 4 Control
         

 

Price

Delivery

Terms

F.O.B.

See pricing above

Stock, Subject to Prior Sale

Net before Shipment

Point of Destination

         from Warehouse



 

One Preowned 8' Mechanical Plate Roll

Specifications 

      Bending Length: 96" 
      Top Roll Diameter: 6-3/8" 
      Motor: 7-1/2 HP 
      Floor Dimensions: 156"L x 48"W

 

Equiped With:

          Power Bending Roll Adjustment 
          Manual Pinch Roll Adjustment 
        Manual Drop End 

Price

Delivery

Terms

F.O.B.

$ 8,900.00

Stock, Subject to Prior Sale

Net before Shipment

Point of Destination

         from Warehouse


  


 

One Preowned Heller Initial Pinch Mechanical Plate Roll


Specifications

       Model S 2050/6 Sergi

          Maximum Bending Length: 6' x 6" 
          Diameter Top Roll: 6.7" 
          Pre-Bend Capacity Mild Steel: 3/16" 
          Rolls: 3, Initial Pinch 
          Working Height: 33" 
          Motor: 230/460V, 3 PH 
          Approximate Shipping Weight: 5,500 LBS 
        Manual Adjustment on Pinch Roll 
 

Price

Delivery

Terms

F.O.B.

$16,500

Stock, Subject to Prior Sale

Net before Shipment

Point of Destination

         from Warehouse


 



One Preowned Webb 3 Roll Initial Pinch Plate Roll


Specifications

       Model 7L

          Capacity: 3/8" 
          Length: 8'2" 
          Roll Diameter: 9" 
          Rolling Speed: 8 to 15 FPM 
          Motor: 10 HP/Speed 1200 
          Floor Space: 77" x 214"
          Weight: 13,250 LBS 

          -Electrical control panel includes fused disconnect, transformer, relay, magnetic starters for each motors
          -Remote electrical console with controls mounted for main drive and adjusting motors 
          -Full length safety treadle for emergency stopping across front and back 
          -Mechanical indicator or digital readout for positioning the rear roll 
          -Steel frames 
          -Bronze bushing for all rolls 
          -Top roll machined from 1040 carbon steel 
          -Lower front and rear roll machined from 1040 carbon steel with feed grooves in both grooves in both rolls 
          -Steel deck plates 
          -Main base fabricated from heavy wide flange steel beams 
          -Drop hinge may be lowered and raised manually or by air cylinder. When drop hinge is lowered, the top roll automatically lifts up so a fulled rolled cylinder can be easily removed. When drop hinge is raised, the top roll will lower automatically to align with drop hinge. 
          -Air valve to operate air cylinder from drop hinge 
          -Clamp to secure drop hinge 
          -Jaw coupling on rear connecting shaft for adjusting roll for cone rolling 
          -Main drive gear guards which cover the three roll drive assembly, main drive pinion, friction clutch on top roll, final drive pinion and belt gear 
          -Standard motors are dual voltage: 230/460-3-60 
          -Steel tail frame 
        -Rear roll with feed grooves, main drive speed reducer that operates in oil bath, main drive motor that is equipped with magnetic brake on machine equipped with slip ring motor for variable speed, resistor grid is not shown 
 

Price

Delivery

Terms

F.O.B.

$34,500.00

Stock, Subject to Prior Sale

Net before Shipment

Point of Destination

         from Warehouse


 


 


One New Americor Plate Bending Roll

 


Specifications

       Model 3RSP 130/5

       Year 2016

          Overall length of rolls: 61" 
          Diameter of all rolls: 5.12" 
          Motors: 2 HP drive motor; 1 HP hydraulic system motor 
          Approx. rolling speed: 16.50' per minute 
          Approx. net weight: 4070 LBS 


Features
          All steel frame 
          Most rigid frame, drop end and clamping roll parallelism unit 
          Machine frame stress relieved 
          Upper and lower pinch rolls driven 
          All rolls mounted in ball or roller bearings 
          Powered hydraulic adjustment of the lower pinching roll, w/independent pinching pressure adjustment 
          Powered hydraulic adjustment of the two side bending rolls, w/push button control and electronic digital readouts for roll position 
          Design of lineal guided lower rolls to minimize flat ends 
          Hydraulic drop end 
        Top roll permenantly balanced when the drop end is opened 
Standard Equipment
      Main drive motor w/magnetic brake 
      Hydraulic unit w/motor and controls for lower roll and rear bending roll adjustment and for the hydraulic drop end 
      SAE 1050 high strength steel rolls heat treated (hardened) to 55-60 Rc 
      Portable control console mounted on wheels for operator convenience (allows operator to position for his/her convenience) 
      Components from American and Eurpeon sources 
      Electrics for 3/60/220 or 440, with overload and under voltage protection. 
         Low voltage at the controls. Safety cable at front and rear of machine. 
      Cone bending attachment 
      Powered tilting of rear bending roll for cone rolling 
      Electronic digital readout to indicate position of the rear bending roll 
      Grooves in lower rolls for 1/4", 3/8", 1/2" round bar (must be ordered from the factory to be included at no charge) 
      Male enclosures 
      European made 
        Instruction and parts manual 

    Please contact us for full quotation with options. 

Price

Delivery

Terms

F.O.B.

$POR

Stock, Subject to Prior Sale

Net before Shipment

Point of Destination

         from Warehouse


 

 


 

Machine Tools South - Used and New Machinery - Metal Fabricating, CNC Machine Tools image image image